Casting fails /Reblog Lottery DUO BONUS !

Welcome in this post I share my casting experience as you may guess from the title things didn't work out, but I ain't quitting, I learned and will adapt.

I gave it a go on the weekend and it was a bit of a rough patch nothing seemed to be going my way this last weekend and this casting fail was a part of it but there was a lot more like me breaking one of my printers, I ordered a part for it and should be able to fix it when it comes in so that's no biggie, and I still have 3 functioning machines.

The reason for my failure with the casting is bad preparation and also some design oversights, but we get into that a bit later in this post.

It came with this safety sheet and it basically said don't inhale the particles, that was a real bummer because initially I wanted to snort some lines of the stuff to be one with the metals.

I got a casting kit from amazon came with a few more things but this is all I needed for my first trial.

My idea was putting my casting mold pieces with my casting support system in the bottom of this 3d printed square I used as a single sided flask I packed it with casting sand and then would flip it over, this way I could get maximum detail and an even base.

Things didn't work out great for one the wood I used was too thin and with the weight of the sand the bottom had some give making it harder to make it totally even but I settled but then I got into my second problem extraction, as you can see bellow I mushed up the mold when I took out the pieces, I then tried again with the stamping method but like I mentioned my work surface was not very sturdy and I had slightly better luck but still sub par results, also it seems my circuit breakers could not handle the printers and my electric kiln running at the same time I was gonna base the crucible with borax but like I mentioned it was too much power demand on my electrical system, so moving forward I will have to turn off the printers and other power hungry appliances while I am trying to cast.

I will be taking the lessons I learned and trying my hand at it again, I had ideas to overcome the challenges of a a clean extraction, one was to add 4 holes with the one in the middle holding a magnet and have a tool that will latch on and take out the piece another idea is to heat insert a nut so that after I can put in a screw and have a handle of sorts to pull it out.

Another idea is to make a rig that will press and extract the pieces evenly but that is something I will have to try later on.

There is some other methods that I will be trying later too like lost wax casting that may be able to deliver better results and perhaps at better scale with the use of a casting tree, the only issue with lost wax casting is that it's not reusable it's only good for a single cast as you burn out the mold negative leaving behind a plaster mold that will have to be broken up after casting.

---

Reblog lottery

We got 33 participants for our reblog lottery this time around.

@blitzzzz @chaosmagic23 @cup-bearer @daddydog @daniasi @duckmotor @ecencypoints @ekads @ene22 @ferod23 @fonestreet @henruc @hjrrodriguez @ijelady @juralyrondina @kungfukid @ladymisa @laurajimeneza @mirroredspork @monsterbuster @mrf83 @mxm0unite @olaf.gui @polygonpirate @servelle @stekene @sudutpandang @sylmarill @trautenberk @vaynard86 @vrezyy @ydm6669 and @youloseagain

and the winner this time around is....

and we got a dud, better luck next time.

@sylmarill! Congratulations enjoy your 10% profit share on this post, 0.33 DUO tokens, 5 HBI units more about HBI units here

The reblog lottery continues so be sure to reblog this post to qualify, for a minimum 10% profit share, 0.33 DUO token and 5 HBI units (bonus wheel) on my next post

This is all done automatically and I apply the winner to be a beneficiary for the post.

Only reblogs before tomorrow 8pm Eastern Standard Time qualify for the lottery.

---

I am a financial advisor ! If you can't take personal responsibility for you investing, I hate to brake it to ya, but you ain't nothing but a sucka, you supposed to lose your shit.

@bitcoinman's bits of wisdom

• Invest only what you can afford to lose and be mindful of the potential risks.
• Unless you can accept delivery stay away from futures and stick to physical.
• Leverage is a great tool for losing money fast.
• Numismatics for the lows stick to smart stacking baby.
• Be cautious of new schemes in crypto, like ICOs, DeFi, and NFTs, do your research before investing.

---

BUY/SELL PRECIOUS METALS WITH HBD + PRECIOUS METALS TOOLS AND ACCESSORIES

---

Buy DUO and stake to receive Hive dividends, tip others, have your posts curated and grow Hive!
Learn more about DUO here
https://tribaldex.com/trade/DUO
https://hive-engine.com/trade/DUO

You can find out more about the #silvergoldstackers community in this post here

HOC Hive Onboarding Committee discord link here

---

Weekly Post Schedule

Day	Post
Monday	Art&3D
Tuesday
Wednesday
Thursday
Friday	Stacker of the week
Saturday	Lazy Saturday post
Sunday

---

Profit share

10% of this post earnings go to @sylmarill for being our reblog lottery winner.

---

That's it for today's post thanks for stopping by your support is truly appreciated.

Posted Using InLeo Alpha